Heute: die Folienfront chick und modern, aber empfindlich , today: The foil front chick and modern, but delicate

in #steemit7 years ago

kitchen-2490416_1280.jpg

Bei der Folienfront handelt es sich um eine polymere Frontoberfläche welche auf eine MDF Platte gezogen wird. Dies mit einem Tief Ziehverfahren. Zu erkennen sind diese Fronten meist daran, dass sie keine Kanten und Fugen am Rand der Front aufweisen, sondern die Folie auch um die Ecken gezogen wird und diese entsprechend ummantelt.
Und genau da Fängt auch das Problem dieser Frontkategierie an. Die Oberflächen sind zwar sehr Pflegeleicht an sich, jedoch zerkratzen Sie schneller als Schichtstoff oder Melaminharzfronten.
Das größte übel jdeoch ist Wasserdampf. Dieser führt dazu, das die Kanten sich ablösen. Das sieht unschön aus und wird im Lauf eines Küchenlebens immer schlimmer.
So sollte man darauf achten das man keine Wasserkocher unterhalb der Hängeschränke nutzt. Auch eine Kaffemaschiene kann schon ausreichen. Bei Backofen und Dunstabzug sollte darauf geachtet werden, das Hitzeschutzprotektoren mit verbaut werden.Diese sehen nicht besonders schön aus, Schützen jedoch die Front.
Der Geschirrspüler sollte nach einem Waschgang immer ganz geöfnet werden. Noch besser ist es zu warten bis der Wasserdampf sich wieder gelegt hat. Das dauert meist bis zu einer halben Stunde.

Die Folienfront gibt es in verschiedenen Oberflächenbehandlungen. Von Matt über Ultramatt bis hin zu hochglänzend ist alles; auch in diversen verschiednenen Farben möglich.
Vor allem kommt die Frontkategierie im Landhausbereich vor.
20170822_132933.jpg
Denn was mit einer Schichtstofffroten (Material nicht dehnbar genug so das es reißen würde) nicht möglich ist, läßt sich hier dank dem tief ziehverfahren und der MDF Platte ohne weiteres realisieren. Die Kasette.
So handelt es sich um eine kostengünstigere Alternative im Vergleich zur Lackoberfläche, welche gerade bei Landhausfronten oft angeboten wird.

Einige Hersteller bieten die Folienfronten im modernen Bereich mitlerweile auch mit einer Dickkante an. So ist eine sehr softe Oberfläche möglich und trotzdem ist die Kante geschützter. Das entspricht dem aktuellen Zeitgeist und wird als sehr Modern Empfunden.
20170822_133021.jpg
Fazit: Dank der weiterentwicklung der Elektrogeräte und gerade wenn man etwas mit dem Wasserdampf aufpaßt hat man eine kostengünstige Alternatife zur Lackfront.
Jedoch kann einem kein händler Garantieren das mit der Oberfläche auf langer sicht nicht doch Probleme auftauchen. Somit rate ich jedem etwas mehr Geld auszugeben und eine lackierte Oberfläche zu kaufen. Wer nicht so viel Wert auf die Optik einer Lackfront legt, kann auch eine HPL oder Melaminharzbeschichtete Front nehmen. Diese ist wesentlich Robuster.

Vielen Dank für Eure Aufmerksamkeit

in Ostfriesland sagen wir "holl die Munter"


in english:
The foil front is a polymeric front surface which is pulled onto an MDF plate. This is done by a deep drawing process. These fronts are usually recognizable by the fact that they do not have edges and joints at the edge of the front, but the film is also pulled around the corners and encased accordingly.

And that is precisely where the problem of this front-line strategy begins. The surfaces are very easy to maintain, but they scratch faster than laminate or melamine resin fronts.
The biggest evil is water vapor. This causes the edges to peel off. This looks unattractive and is getting worse and worse in the course of a kitchen life.
So you should pay attention that you use no water cookers below the hanging cabinets. Even a coffee machine can be enough. In the case of oven and fume extractor, care should be taken to install the heat protection protectors. These do not look particularly nice, but protect the front.
The dishwasher should always be completely opened after a wash cycle. It is even better to wait until the water vapor has settled again. This usually takes up to half an hour.

The foil front is available in various surface treatments. From Matt to Ultramatt to high-gloss is everything; Also in various different colors possible.
Above all, there is the front line in the country house sector.
For what is not possible with a laminate frost (material not stretchable enough so it would tear) is possible, thanks to the deep drawing process and the MDF panel. The cassette.
This is a more cost-effective alternative compared to the lacquer surface, which is often offered in country fronts.
Some manufacturers offer the foil fronts in the modern area mitlerweile also with a thick edge. Thus, a very soft surface is possible and nevertheless the edge is more protected. This corresponds to the current Zeitgeist and is perceived as very modern.
Conclusion: Thanks to the further development of the electrical appliances, and especially when you take care of the water vapor you have a cost-effective alternative to the lacquer front.
However, no dealer can guarantee that with the surface in the long run not problems but emerge. So I advise everyone to spend more money and buy a painted surface. If you do not care about the appearance of a lacquer front, you can also take an HPL or melamine resin-coated front. This is much more robust.

Thank you very much for your Attention
kitchen-2411847_1920.jpg

Sort:  

Very, nice blog. thank you for joining steemit.vote
Please upvote the steemit.vote users from the list.

Nur weiter so! Das wird was! Nur Geduld. Upvoted

Coin Marketplace

STEEM 0.18
TRX 0.13
JST 0.028
BTC 57286.76
ETH 2998.80
USDT 1.00
SBD 2.26