ty for the reply ,,would you mine if you could help me how or what to type in.
i still getting this error
PCIe Bus Error: Severity=Corrected, type=Physical Layer, id=00db(Receiver ID)
device [8086:aZee] error status/mask=00000001/00002000
[0] receiver error (first)
Hey man, sorry for the late reply, I just now noticed there were new comments on this. First please double check that you followed all of the instructions exactly. If you're positive that you didn't have any typos etc, then you can try replacing pci=noaer with pci=nomsi and run through the rest of the steps as I listed them. See if that works. If you're still having trouble get back to me and I will keep a closer eye on this post so I can get back to you in a timely manner.
Thank you for your reply,,too sad i can't make it work when i try to close and save it it says error writing file or directory doesn't exist i follow all the instruction above..
pls enlighten me did i type this correctly
nano etc/default/grub
(there some message on tool bar saying [directory 'etc/default' does not exist]
Change GRUB_CMDLINE_LINUX_DEFAULT="quiet" to GRUB_CMDLINE_LINUX_DEFAULT="quiet pci=noaer"
after pressing CRTL+X it say error writing file or directory doesn't exist..
I'm not sure what's up with that. Try emailing the admin, he'll have a much better idea what's going on than I do. It sounds like something go fucked up with the file structure but I'm not knowledgeable enough when it comes to linux kernels to give you specific advice.
Seems like permissions problems, I've done using miner/miner (user/pass), miner is an admin user which means you better use it and do it as follows:"sudo nano etc/default/grub" (personally I use vi/vim) and update the line as this article suggests (thanks btw for this post).
The latest version does not have "quiet", so adding "pci=noaer" between the quotes is enough. Best luck and thanks.
ty for the reply ,,would you mine if you could help me how or what to type in.
i still getting this error
PCIe Bus Error: Severity=Corrected, type=Physical Layer, id=00db(Receiver ID)
device [8086:aZee] error status/mask=00000001/00002000
[0] receiver error (first)
Hey man, sorry for the late reply, I just now noticed there were new comments on this. First please double check that you followed all of the instructions exactly. If you're positive that you didn't have any typos etc, then you can try replacing pci=noaer with pci=nomsi and run through the rest of the steps as I listed them. See if that works. If you're still having trouble get back to me and I will keep a closer eye on this post so I can get back to you in a timely manner.
Thank you for your reply,,too sad i can't make it work when i try to close and save it it says error writing file or directory doesn't exist i follow all the instruction above..
pls enlighten me did i type this correctly
nano etc/default/grub
(there some message on tool bar saying [directory 'etc/default' does not exist]
Change GRUB_CMDLINE_LINUX_DEFAULT="quiet" to GRUB_CMDLINE_LINUX_DEFAULT="quiet pci=noaer"
after pressing CRTL+X it say error writing file or directory doesn't exist..
I'm not sure what's up with that. Try emailing the admin, he'll have a much better idea what's going on than I do. It sounds like something go fucked up with the file structure but I'm not knowledgeable enough when it comes to linux kernels to give you specific advice.
Seems like permissions problems, I've done using miner/miner (user/pass), miner is an admin user which means you better use it and do it as follows:"sudo nano etc/default/grub" (personally I use vi/vim) and update the line as this article suggests (thanks btw for this post).
The latest version does not have "quiet", so adding "pci=noaer" between the quotes is enough.
Best luck and thanks.
There is a typo:
"nano etc/default/grub"
try this
"nano /etc/default/grub"
Should be able to edit it....