OTOMOTIF Motorcycle - Checking and Repairing Motorcycle Ignition Coils with Simple Tools

---

---

Tonight I want to explain again to you steem users, while doing motorcycle repairs, because my friend had problems with expensive repair costs in several other workshops, as a friend in the village, so, he told me about his motorcycle problem. I can only smile, because I am not a good mechanic. because my friend once told me, so, he came to my house yesterday, and fixed it today:

Damage Problems According to Motorcycle Owners "Honda Beat Motorcycle"

• in the morning it is difficult to start like a dead battery
• when on the road it suddenly dies, turns on again.

with complaints about the damage, then, I bought some additional tools, such as:

• 1 meter cable IDR 9,000, -
• 2 clamps around IDR 18,000, -

Well, after I assembled it, it looks like the picture below:

---

---

the tool that I assembled above, of course based on the inspection of the sensor section for two-wheeled vehicles that have an INJECTION system, so before further work, so that what we do can run well. next I did it with a check with a sensor checking tool, with the tool below:

---

---

My friend experienced problems with high repair costs at several other workshops, as a friend in the village, so, he conveyed his motorcycle problem. I could only smile, because I am not a good mechanic. because my friend told me before, so, he came to my house yesterday, and fixed it today:

after that, we do a basic inspection on the vehicle directly, then, after I checked the fuel pump section, it was fine and had fuel in the motorcycle tank, the next thing I checked was the coil, and after I checked this below section,

the tool that I assembled earlier, I clamped the black part at the end of the spark plug of the motor vehicle. so that you understand how to install it during the inspection, I removed the spark plug and installed it as shown in the picture below "this is just an example, when checking, the spark plug is still attached to the engine part ok":

---

1 . INSTALLATION METHOD

---

1 . black part like this:

---

---

2 . red part like this:

---

---

2 . IGNITION CHECK

The results of the examination will be as below:

---

do it with two different distances, distance 1 and distance 2, so when doing this test, we can see whether the ignition can work well or not perfectly ok.

---

• Distance 1 tool and ignition exit position

---

---

• Distance 2 tools and ignition exit position

---

---

How to do it is, below :

---

by pressing the starter button, the results will be seen at the end of the ignition system is very small and there is a spread of ignition to the vehicle body, making the closest part of the vehicle become irregular ERROR, so that some vehicle SENSORS experience UNSTABLE performance. therefore, when we drive this vehicle there are several factors that have been mentioned by my friend above to be problematic.

after I found this disease, then without waiting long I immediately removed this ignition system part or ignition coil, to fix it.

---

3 . IGNITION LINE WIRING REPAIR

---

1 . Step one, cut the end to find the ignition wire." see picture below "

---

---

2 . wrap the ignition cable with a special plastic heat-resistant wrap, so that it can last before replacing the new one. "see picture below"

---

---

4 . FINAL RESULTS OF REPAIR AND TESTING

---

After everything was done, then, I did the 2nd method in the position of the distance between the ignition outlet hole and the clamp that I assembled above, to ensure the ignition range obtained, and the results turned out to be very surprising to me, let's see the picture below:

---

---

In the image above, you can see again that the ignition emitted from the ignition coil is very large, compared to the first ignition, before we repaired it, in the image below:

---

1 . BEFORE FIXED

---

---

2 . AFTER FIXED

---

---

Well, now you steem users have seen the results, by Checking and Repairing Motorcycle Ignition Coils with Simple Tools at home and the problem experienced by my friend in the village is over. finally everything was reinstalled on the socket and ignition hole of this Honda Beat model vehicle,

and after being tested, finally the vehicle was no longer problematic, only my friend was waiting for his finances to improve in the future, so that he could replace it with a new original ignition coil, which is priced at several official workshops around IDR.140,000, -

finally my second friend, will not be late again taking his child to school every morning. because his motorbike is no longer problematic now. and went home with a happy smile.

at the end of this word, I just want to advise steem users who have motorbikes, to always do regular servicing, to avoid your vehicle from being damaged, and check for damage from the smallest first, and start checking the fuel, ignition and engine compression, by starting this, your motorbike can definitely be turned on again. even though there are minor repairs.

If this post about ignition is useful, please comment below and thank you to those who have supported this motorcycle automotive topic, so that I am more enthusiastic in telling and explaining how to repair motorcycle ignition based on my experience because my motorbike was previously damaged.

regards
@sultan-aceh

---

---

---

---

---

---